|
Logic 3.0
Technology (L3)
 Added
Value
-
Built-in
3-channel,
315MHz radio
receiver accepts
up to 23
Security+® or
unlimited DIP
switch remotes.
3-button remotes
can be
programmed for
open/close/stop
operation.
-
Maintenance
Alert System™
establishes a
routine
maintenance
schedule based
on the number of
cycles or
calendar date.
Includes
self-diagnostic
system that
allows you to
troubleshoot up
to eight
different error
codes.
-
Timer-to-Close
allows
programming in
5-sec or 1-min
increments.
Commercial or
industrial
photo-eyes
required.
-
Thermal motor
overload can be
easily reset
from the
3-button floor
level control
station
Reliability &
Programming Simplicity
-
Switchless motor
eliminates stuck
start switch and
motor
malfunctions on
single-phase
operators
-
All high-voltage
connections have
been removed
from the board
for safety and
ease of service
-
Diagnostic LEDs
speed
installation and
troubleshooting
-
Motor direction
jumper lets you
change motor
direction by
simply moving a
jumper
Mechanical
Reversing Contactor
Circuit (M):
(115V, 208/230V, 460V,
575V, 24V NEC Class 2
Circuit with 40VA
transformer) Industrial
linear contactor
provides significantly
longer control runs than
conventional contactors.
Standard Features
Motor:
Continuous-duty
high-starting torque
motor with instant
reverse and overload
protection. Available
in 1/3, 1/2, 3/4 and 1
HP; single- or
three-phase. Removable
without affecting limit
switch settings.
Drive
Reduction:
First-stage heavy-duty
5L V-belt; second-stage
#41 chain; output on
trolley #48 chain on 1/3
and 1/2 HP; #41 chain on
3/4 and 1 HP.
Emergency
Disconnect:
Spring-loaded for
emergency manual
operation.
Wiring Type:
B2, C2, D1 and E2
wiring types are
standard and easily set
using a selector dial on
the Logic 3.0 Control
Board (L3). T and TS
wiring can be activated
with use of a CPS-L or
CPS-LN4. Reversing
Contactor Units (M) have
C2 wiring standard and
B2 available by simply
moving a jumper wire.
Operators are pre-wired
to accept a sensing
edge, photoelectric
sensors, radio controls
and most types of access
control equipment.
Failsafe wiring can be
selected with use of a
CPS-L, CPS-LN4 or
failsafe edge and CPS3
card.
External Radio
Control Terminal:
Quick, convenient
connections for
retrofitting or adding
radio controls on logic
or mechanical operators.
Bearings:
Ball bearings on output
shaft; heavy-duty,
oil-filled bushings on
reduction shafts.
Brake:
Solenoid-actuated brake
is standard on 3/4 and 1
HP units to prevent
coasting of door.
Optional on 1/3 and 1/2
HP units.
Friction
Clutch:
Adjustable, helps
protect against major
damage to door and
operator should the door
meet an obstruction.
Construction:
NEMA 1 type electrical
box, heavy-duty 11-gauge
steel frame with durable
powdercoat finish, all
reduction sprockets
drilled and pinned to
shafts.
Push Button
Station: 3-button
station comes standard
and has open/close/stop
functionality.
Quick-Mount
Header Bracket:
For fast, swing-up
mounting.
Rail Assembly:
High-strength dual
L-rail track with nylon
quiet-gliding chain
guides on rail spacers
for quiet, smooth
operation.
Control Accessories
CPS® Commercial
Protector System®:
(recommended) A
“non-contact” photo
safety sensor designed
to sense an obstruction
and signal the door
operator to reverse to
open.
Sensing Edge:
(recommended) Designed
to sense an obstruction
and signal door operator
to stop or reverse as
desired. An electric or
pneumatic sensing device
can be added to bottom
edge of door.
Available Plug-in
Options for Logic 3.0
(L3)
Auxiliary
Contact:
Used to operate
security, warning,
heating or other 5V to
240V devices. Features
both normally open and
closed contacts that
actuate in conjunction
with limit switches.
Warning Signal:
Red/green light module
provides safety warning
prior to close (when
using timer-to-close
feature). Also supports
audio warning devices
and includes down
mid-stop feature.
CPS3 Option:
Enables the addition of
a second set of
photo-eyes or 2- or
4-wire, self-monitoring
edge. |
